Eekay E Silicon 521 Heat Resistant Silicon Based Aluminum Paint 600⁰C
Eekay E Silicon 521 Heat Resistant Silicon Based Aluminum Paint 600⁰C
High-temperature coatings are required to protect metal surfaces such as barbecues, cookers, non-stick cookware, engine components, boilers, vehicle exhausts and even the working parts of rockets from oxidation over an extended period. High temperature paint for metal is not designed to deliver fire retardant properties, but can be used on industrial chimneys, furnaces, commercial and domestic ovens applications.The most commonly used heat resistant paint colours include black and silver (also referred to as aluminium).
Product Features
Resistant for dry heat up to 600⁰C.
Good water resistance.
Good weather resistance.
Can be applied on MS surface.
For painting of Heavy Equipment’s, vessels, silencers, radiators, ovens etc to provide dry heat resistance, Interior / Exterior of chimneys, Chemical unit, refineries etc.
| Color | Silver / Black |
| Finish | Glossy |
| Volume Solids | 25 |
| Recommended DFT | 90 to 100 Sq Ft / liter / coat |
| Drying Time | Surface Dry 90 minutes, Hard Dry 16 Hours |
| Viscosity | 40 – 45 Sec |
| Over coating | Interval at 30⁰C Minimum 16 hours, Maximum Unlimited provided the surface is clean and dry from all contamination |
| Flash Point | Not less than 24⁰C |
| Recommended Thinner | Eekay H. R. Thinner |
Direction to use
Surface Preparation
General
Surface preparation and substrate condition should be dry and free from all contaminations, dust, grese, oil, etc. surface to be sufficiently roughened prior to painting.
Surface should be checked and treated in accordance with solvent cleaning.
Blast Cleaning
Steel, blast clean to Sa 2.5 of Swedish Specification
A blasting profile of (Rz) 35 – 50 microns is recommended.
Application Conditions
Substrate temperature should be atleast 3⁰C above dew point but not above 45⁰C
Relative Humidity should be ≥85%
Good ventilation is required in confined areas to ensure proper curing.
Mixing
If settling is observed in the drum, loosen the material with the help of hand stirrer, followed by power driven stirrer if needed.
Add medium and paste and properly stir to get a homogenous mixture.
| Application | Recommended Thinner | Volume of Thinner | Nozzle orifice | Nozzle Pressure |
| Brush / Roller | Eekay HR Thinner | Not required | NA | NA |
| Air Spray | Eekay HR Thinner | 5 - 15% | 1.5 – 3.00 mm | 0.3 – 0.4 MPa |
| Airless Spray | Eekay HR Thinner | 0 - 10% | 0.28 – 0.33mm | 10 – 13 MPa |
Cleaning
Do not allow the product to remain in hoses, gun or spray equipment. Clean all equipment’s immediately after use with Eekay HR Thinner. It is recommended to flush out spray equipment during the course of working.
Product Characteristics
The maximum performance is achived after complete drying.
At higher relative humidity, drying may get affected.
The product must not be applied on hot surfaces.
Storage and Packing
Store in cool and dry place.
Store in accordance to local regulations.
Packing will be made available in 4 and 20 liters pack size.
Safety Information
As a general measures, inhalation of solvent vapors, contact with eyes should be avoided. While application area should be well ventilated.
Ishwar Krupa, Chiplunkar road, Near Ramkrishna Hotel Chitaranjandas Road Ramnagar Dombivli (E)
+91 92214 61960 +91 97691 75577
Eekay Product & Co. | Developed By Sanmisha Technologies