Eekay Epoxy Polyamide Red Oxide Primer
Eekay Epoxy Polyamide Red Oxide Primer
Eekay Epoxy Polyamide Red Oxide Primer is a 2K system especially formulated by using selected chemical resistant & weather resistant pigments. They form good adhesion on for metal or masonry surface for exterior & interior use. It can also be used in the storage of chemicals of other Petroleum products. Excellent adhesion on Eekay Epoxy Polyamide Finish.
Product Benefits
Good water and humidity resistance.
Anticorrosive and rust protective.
Easy in application, brushing and sprying.
Excellent adhesion over MS surfaces.
Product Features
Washable with potable water.
Excellent resistance to saline, marine and chemical environment.
Free from lead and chromate containing pigment.
| Color | Red |
| Gloss | Matt |
| Volume Solids | Approx 50 – 55 % |
| Recommended DFT | 35 – 40 Microns |
| Theoretical coverage capacity | 10 – 11 sq. mtr/ltr |
| Drying time at 30⁰C | Surface Dry – 1 Hour Hard Dry – 12 hours Full Cure – 7 days |
| Over coating interval at 30⁰C | Minimum : 12 to 14 hours Maximum : 30 days provided the surface is clean and dry. |
| Mixing Ratio | 4:1 |
| Pot Life | 4 hours |
| Induction time | 30 – 35 minutes |
Direction to use
Surface preparation and substrate condition should be dry and free from all contaminations, surface to be sufficiently roughened prior to priming.
Surface temperature must be atleast 100 C and not more than 450C.
Steel, abrasive blast clean to min Sa 2 1/2Swedish method.
Relative humidity should be below 80%
Good ventilation is required to ensure proper curing
Mixing
Eekay Epoxy Polyamide Red Oxide Zinc Chrome Primer is supplied in two packs. Stir the base and hardener separately. If settling is observed in the base or hardener, loosen the settled material with hand stirrer followed by power stirrer for quick homogenous mixing.
Mix hardener gradually in to the base under continuous stirring as per the mixing ratio. Once the unit has been mixed it should be used with the pot life of 2 hours. Post use of unused base and hardener, close the lids tightly to avoid contact with atmospheric moister.
Thinner if added should be after mixing the components and post the induction time. Addition of too much thinner will lead to reduced sag resistance.
| Application | Recommended Thinner | Volume of Thinner | Nozzle orifice | Nozzle Pressure |
| Brush / Roller | Eekay EP Thinner | 0 – 10% | NA | NA |
| Air Spray | Eekay EP Thinner | 5 – 15% | 1.5 – 3.00 mm | 0.3 – 0.4 MPa |
| Airless Spray | Eekay EP Thinner | 0 – 15% | 0.38 – 0.46mm | 10 – 13 MPa |
Storage and Packing
Store in cool and dry place.
Store in accordance to local regulations.
Packing will be made available in 1, 4 and 20 liters pack size.
Safety Information
As a general measures, inhalation of solvent vapors, contact with eyes should be avoided. While application area should be well ventilated. In case of eye contact wash with plenty of clean water and take medical help if necessary. Use protective equipment’s like rubber / polyethylene gloves, safety goggles and face mask while handling the paint.
Please Download the Material Safety Data Sheet
Ishwar Krupa, Chiplunkar road, Near Ramkrishna Hotel Chitaranjandas Road Ramnagar Dombivli (E)
+91 92214 61960 +91 97691 75577
Eekay Product & Co. | Developed By Sanmisha Technologies